/
EN
/

Site Navigation

Your Account

Choose Language

Titan Aero Smoothieware Configuration

Written By: Gabe S. (and one other contributor)
  • Comments: 0
  • Favorites: 0

Difficulty

Easy

Steps

9

Time Required

00:05:00 - 00:15:00

Sections

1

Flags

0

    • First things first: you're going to need a copy of Smoothieware.

    • If you are upgrading an existing 3D printer to use a Titan, you should try to get a copy of your current firmware from your printer's manufacturer.

    • If you're building a new printer, or simply want to upgrade to the latest version of Marlin, download it at http://smoothieware.org/getting-smoothie

    • If you download a fresh version of Smoothieware you'll have to configure more settings than the ones mentioned in this guide so that it will work well with your printer.

    Edit

    • Unzip Smoothieware from the zip file you downloaded and put the resulting folder anywhere on your computer for safe keeping.

    • You will be working with the config file.

    Edit

  3. If your old extruder was ungeared, you'll notice that your new Titan extrudes backwards!

    • If your old extruder was ungeared, you'll notice that your new Titan extrudes backwards!

    • Add or remove a ! from the number after the following line: extruder.hotend.dir_pin.

    Edit

  5. The next thing we'll have to update is your printer's E-steps-per-mm.

    • The next thing we'll have to update is your printer's E-steps-per-mm.

    • Your slicer will generate G-Code for your printer, which will tell it to extrude a certain length (in millimeters) of filament. Your printer takes those lengths of filament and calculates how much it should rotate your Titan's stepper motor to push out the expected amount filament. This number is used to make that conversion

    • First, we'll start with a ball-park estimate of your E-steps-per-mm, and then we'll fine-tune it.

    • If you're using the standard Titan Slimline motor, start with 837 Steps-per-mm

    Edit

  6. Over USB Connection

    • Over USB Connection

    • Use a printer control software to connect to your printer. Send the command M92 E<your number here>to your printer.

    • Then, send M500 to store your settings

    • Update your config file manually:

    • Update the following line with your new number: extruder.hotend.steps_per_mm. Upload your firmware as normal.

    Edit

  7. To get a more exact value for your E-steps-per-mm, measure the exact amount of filament that is pushed out of your extruder. Load filament into your extruder, just until it is gripped by the drive shaft (you can't pull it out without moving the large gear turning) Mark your filament at the top of the idler arm or PTFE tubing with a pen or permanent marker .

    • To get a more exact value for your E-steps-per-mm, measure the exact amount of filament that is pushed out of your extruder.

    • Load filament into your extruder, just until it is gripped by the drive shaft (you can't pull it out without moving the large gear turning)

    • Mark your filament at the top of the idler arm or PTFE tubing with a pen or permanent marker .

    • Tell your printer to extrude 100mm of filament. Use your printer's LCD screen, or send it: G92 E0, then G1 E100 via your printer control software.

    • You may need to heat your HotEnd before your printer allows you to extrude filament. You can use M302 command to get around that.

    • Mark your filament again at the top of your idler arm or PTFE tubing

    • Eject your filament.

    Edit

  8. With a ruler or calipers, measure the distance between the two marks on your filament. If the distance wasn't exactly 100mm, use a proportion to calculate a more precise E-steps-per-mm value. Enter that new value into your firmware or EEPROM as you did before.

    • With a ruler or calipers, measure the distance between the two marks on your filament.

    • If the distance wasn't exactly 100mm, use a proportion to calculate a more precise E-steps-per-mm value.

    • Enter that new value into your firmware or EEPROM as you did before.

    Edit

  9. On the SD card that contains your printer's firmware, update the configuration file with the following line: temperature_control.hotend.thermistor Semitec

    • On the SD card that contains your printer's firmware, update the configuration file with the following line: temperature_control.hotend.thermistor Semitec

    Edit

    • Save the firmware to your SD card as you normally would. If you're having issues, check with your printer's manufacturer.

    • If you're unsure of how to update your printer's firmware, check with its manufacturer.

    Edit
Conclusion

You're all done. Enjoy your new Titan!

Author

with 1 other contributor

Gabe S.

Member since: 08/08/2017

14,576 Reputation

41 Guides authored

0 Comments

Add a comment

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 0

Past 30 Days: 3

All Time: 1,345