Skip to main content
  1. Gather
    • Gather

    • 30mm Fan

    • 2 Plasti-fast Screws

    • Cyclops/Chimera Heatsink

  2. The sticker of the fan must face towards to fins of the heatsink in order that the fan blows air through the heatsink.
    • The sticker of the fan must face towards to fins of the heatsink in order that the fan blows air through the heatsink.

    • Plan the direction you want your wire from your fan to come out.

    • Screw in the fan onto heatsink using the two supplied silver self tapping screws for metal. Use the top-right and bottom-left screw holes.

  3. Gather
    • Gather

    • 2 Collets

    • Heatsink

    • PTFE Tubing

  4. Because the Cyclops/Chimera heatsink is so compact, it is best to use it with a bowden setup. If you still want to use a direct setup, skip inserting the collet, but make sure you still insert PTFE tubing to guide filament through the heatsink.
    • Because the Cyclops/Chimera heatsink is so compact, it is best to use it with a bowden setup.

    • If you still want to use a direct setup, skip inserting the collet, but make sure you still insert PTFE tubing to guide filament through the heatsink.

    • Press in the two collets into the holes with the brass ring.

    • Connect the two collet clips

  5. Gather
    • Gather

    • Heatsink

    • 4x 3mm Grub Screws

    • The Smaller, 1.5mm Hex key

  6. Screw in the 4 grub screws into the sides of the heatsink.
    • Screw in the 4 grub screws into the sides of the heatsink.

    • These screws will tighten the heat breaks to the heatsink later. For now, just screw them in so you don't lose them.

    • Use the 3 M3 dome screws left over to mount your heatsink to your printer, when you're ready to do so.

    • Gather

    • 2x 2.5mm Steel Balls (Don't lose them!!!)

    • 2x M4 Grub Screws (larger than the ones in the cold side kit)

    • Cyclops Plus Heater Block

    • Cyclops Heat Breaks x 2 (Note that the Cyclops heat breaks have a flat bit on the lower threading, compared to the Kraken heat breaks which are completely smooth)

    • Cyclops Nozzle

  7. One side at a time: drop the steel balls into the threaded channels on the sides of the heater block Screw in a grub screw on each side to hold the ball in place Don't worry about the tightness of the screws, we'll be hot-tightening them later
    • One side at a time: drop the steel balls into the threaded channels on the sides of the heater block

    • Screw in a grub screw on each side to hold the ball in place

    • Don't worry about the tightness of the screws, we'll be hot-tightening them later

  8. Screw the Cyclops heat breaks into the heater block These will be hot-tightened later, so don't worry about tightness
    • Screw the Cyclops heat breaks into the heater block

    • These will be hot-tightened later, so don't worry about tightness

  9. Screw in the nozzle Note that Cyclops nozzles are specific to Cyclops, and are not compatible with V6 or Volcano nozzles
    • Screw in the nozzle

    • Note that Cyclops nozzles are specific to Cyclops, and are not compatible with V6 or Volcano nozzles

    • Don't worry about tightness, we'll be hot-tightening later

    • Gather

    • Heater Cartridge

    • Heater Block

    • M3 Grub Screw x 2

    • Thermistor Cartridge

    • Thermistor cable

  10. Slide the heater cartridge into your heater block. Position it right in the centre. You can have the wires coming out either side of the heater block.
    • Slide the heater cartridge into your heater block. Position it right in the centre.

    • You can have the wires coming out either side of the heater block.

    • Screw in the grub screw on the bottom of the heater block, and tighten to hold the cartridge in place.

  11. Slide the thermistor cartridge into your heater block. Position it in the centre You can have the wires coming out either side of the block, but we recommend that you have them coming out of the same side as the heater to facilitate cable routing
    • Slide the thermistor cartridge into your heater block. Position it in the centre

    • You can have the wires coming out either side of the block, but we recommend that you have them coming out of the same side as the heater to facilitate cable routing

    • Screw in the grub screw on the bottom of the heater block, and tighten to hold the cartridge in place

    • Make sure to not tighten the M3 grub screws too much as this will deform the cartridges and make them very difficult to remove in the future

    • Clean up your wiring now, not later! Make sure your wires won't get snagged anywhere and are nicely organised

    • Plug your electronics into your electronics board

    • Next, we're going to heat up your hotend to tighten the nozzle, heat breaks and the grub screws holding the balls in place

    • Make sure that you place your HotEnd somewhere that can take the heat it will give off!

    • Don't burn yourself when heating your hotend!

    • You should hot tighten at 285°C

    • Begin tightening the M4 grub screws, you will feel the balls slide along the under-sized hole as they progress forwards.

    • When you feel the resistance increase significantly, the balls have reached the end of their travel and you are done.

  12. Tighten the heatbreaks
    • Tighten the heatbreaks

    • You should get ⅛ to ¼ turn out of them now that everything is hot.

  13. Tighten up the nozzle.
    • Tighten up the nozzle.

    • As with the heat breaks you should get ⅛ to ¼ turn.

    • Cool down your HotEnd, and make sure you don't burn yourself on the next steps.

  14. Apply heatsink compound onto the surface of the heat breaks sparingly.
    • Apply heatsink compound onto the surface of the heat breaks sparingly.

    • You don't need to use the whole sachet.

  15. Slide the heat breaks up into the Heat Sink.
    • Slide the heat breaks up into the Heat Sink.

    • Ensure the bottom of the breaks is flush with the bottom of the sink

  16. Tighten the 2 grub screws on either side of the heatsink to secure the heat break in place
    • Tighten the 2 grub screws on either side of the heatsink to secure the heat break in place

    • The grub screws should be tightened up only enough to secure them, excessive tightening of the grub screws will damage the surface of the Heat Breaks.

  17. In your slicer of preference find the retraction settings. In Slic3r this is in printer settings. Start with a retraction length of 1mm
    • In your slicer of preference find the retraction settings. In Slic3r this is in printer settings.

    • Start with a retraction length of 1mm

    • If you experience blobs or stringing on the surface of the print increase the retraction length to 2mm.

    • Do not increase the retraction length more than 2mm as this can lead to molten plastic being pulled into the heat break, increasing the likelihood of jams.

    • Make sure that there are always 2 filaments inserted into the Cyclops + when printing. This also applies if you are only using 1 filament to print with.

    • Printing with only 1 filament inserted will cause molten filament to leak out of the second filament orifice .

Finish Line

One other person completed this guide.

John Bamford

Member since: 08/25/2017

469 Reputation

2 Guides authored

2 Comments

A very detailed description of how to assemble the item. Especially as there are coloured photos of every step and pitfalls to avoid.

Philip Farrington - Reply

At step 11, you should tell the readers that the nozzle should be very close to the heat block, but not quite touching it.

Birdman2010 - Reply

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 8

Past 30 Days: 36

All Time: 2,610